Shark Vacuum Brush Motor Replacement (Full Procedure)
Post Disclaimer
We independently review everything we recommend. The information is provided by Shark Vacuum Brush Motor Replacement (Full Procedure) and while we endeavour to keep the information up to date and correct, we may earn a commission if you buy something through links on our post. Learn more
The vacuum brush does not spin if a motor is damaged or malfunctioning. It is possible that the motor will fail to owe to a broken item inside or a malfunctioning electrical system. You’ll need to replace your shark rotator motor in this situation. But do you know Shark Vacuum Brush Motor Replacement?
Shark Vacuum Brush Motor Replacement
- Find the release button adjacent to the handle at the top of the vacuum pod.
- While pushing the release button, use the handle to raise the pod away from the vacuum nozzle.
- Removing the pod is unnecessary; however, doing so might make it simpler to find obstructions or get to the motor and belt.
- To access the brush roll compartment, press the buttons on the top of the nozzle that says “Brushroll Access.”
- Utilizing the pull tab on the left side, raise the brush roll out of the way.
- Once the brush roll has been installed, you can test it by plugging the vacuum in and operating it in carpet mode. A solid shade of green should be present on the brush roll indicator light.
- The five 5mm Torx #9 screws on the front side should be removed.
- On the bottom face of the nozzle, there are six 7.5mm Torx #20 screws. Remove them.
- A screwdriver extender might be required to reach the screw closest to the nozzle’s center
- You can remove the top panel by raising the top section away from the bottom.
- There will be a lot of loud clicking.
- You can move on to the following step if attempting to remove the belt.
- The 7.5mm Torx #20 screw should be removed in front of the motor.
- The gray block to the right of the floor nozzle is the motor (when the nozzle faces you).
- You can move on to the following step if attempting to remove the belt.
- The motor screw can be seen by removing the panel.
- The motor screw is a 7.5mm Torx #20.
- Take the motor out.

If My Shark Vacuum Brush Has Stopped Working, Is There Anything I Can Do?
Troubleshooting instructions are provided here.
- Determine if the carpet mode is being used.
- If you choose the carpet setting, the brush will spin. Otherwise, it won’t spin if you put it on floor mode.
- Use the carpet mode if you haven’t already done so
- Check to see if there is a blockage in your machine.
- Before you begin disassembling the machine, be sure to turn it off. The machine’s advantage is that the parts can be dismantled easily. As a result, you can see past any obstruction.
To see if there’s a blockage, follow these instructions. Here are a few examples:
Blockage In The Machine
There may be a blockage in your machine. Therefore you should first check to see if the dust cup has been cleared.
Make Sure The Hose Is Working Correctly
- Remove the hose by pressing the quick-release foot pedal. Because of the reduction of suction, you can now see through the tube to check for any obstructions.
- To see if the water is running clear, insert a coin into the waterline. Your hose is clear if the cash exits the opposite end unimpeded.
Make That The Floor Nozzles Are Working Correctly
- You can inspect the floor nozzle to see if the hose, rollers, or any dirt in the wheels are obstructed by anything.
- Press the foot pedal to disengage the fast release and remove the floor nozzle. Now, look for any obstructions on the bottom.
- Remove the brush roll if you detect any hair in the brush roll by pressing the access buttons. A stitch picker can be used to untangle tangled hair. Scissors are an option as well. It is possible to remove hair with a tool provided by Shark. The device is available for purchase as well.
The Filter Must Be Cleaned
- The procedure is straightforward. To access the sponge filter, remove the dust cap from the handle’s top. Clean the filter and dust cap by soaking them in warm water and air dry until the water is crystal clear.
- Give it a day or two. A stench will fill the air if the wet filter is used, so avoid it at all costs.
- Connect the power cord to the machine and reassemble it.
- Your vacuum cleaner is ready to go once removed any obstacles and cleaned the filter. The LEDs on the powerhead should be lit up green.
- Connect the power cord to the machine and reassemble it.
Ascertain Whether Or Not The Equipment Is Functioning Correctly
The lights should be on when you turn on your vacuum cleaner. Green should be the color of the lights. Nonetheless, if the machine is flashing a red signal, you’ve got an issue on your hands. If your Shark continues to flash a red signal, customer support should be called.
Is It Possible To Swap Out Shark Vacuum Parts?
Replacement parts are available for all major and minor components of Shark vacuum cleaners. However, it is essential to remember that each model has a varied set of replacement parts available.
The details you buy should be compatible with your Shark model. You can replace crevice tools and dusting brushes as well as pet multi-tools as well as extension wands and canister caddies as well as filters, brush rolls, and canister caddies, as well as microfiber pads and shark carpet gliders.
Step-By-Step Guide For Replacing the Shark Rotator Motor
You’d first need to remove the motor to replace it. Here’s how to-
Remove The Wheels And The Frame
To remove the vacuum’s body, press the lift-away button and pull on the handle to release it. To get to the bottom of the machine, flip it over. On each side, there are two tiny wheels. Use a spudger to remove them.
Get Rid Of All The Screws And Wires
You will discover nine 16 mm and two 13.5 mm screws. Screwdrivers work well for this. It is necessary to use two 13.5 mm screws, which may be found behind the hose connector. Remove the wire from the base by opening the lid.
Remove The Belt And Roller Brush
Using a screwdriver, remove the two 11 mm screws. It’s time to remove the brush cover. Remove the roller brush by yanking it out. The motor gear and bush are both covered by a roller belt. Could you get rid of it?
Remove The Engine From The Vehicle
Disconnect the wires from the motor by pulling on the pins that hold them to the motor.
Why Isn’t My Shark Vacuum Brush Spinning?
Verify that the vacuum is in the appropriate mode. The switch must be in the Power and Brushroll positions to make the roller spin. The roller won’t move if it is only in power mode. When operating, the brush roll indicator light ought to be green.
Can You Replace The Brush On A Shark Vacuum?
Replacement Brush Roll for the Shark Navigator Vacuum Cleaner from All Parts Inc. OEM-compatible Brushroll made to fit the NV356E and NV42 variants. By ensuring your vacuum’s brush is clean and ready to capture dirt and other debris, you can keep your vacuum operating at its peak efficiency.
Conclusion
Cleaning is a tedious and frustrating job. Most customers prefer shark vacuum cleaners as their primary cleaning instrument because they liberate their owners from the clear burden and entirely modify the clean services.
Shark vacuum cleaners have proven effective and reliable, but there are still a few hurdles for its consumers. Shark Vacuum Troubleshooting recommendations have been tested by many users and are provided for your benefit.
Frequently Asked Questions
Why isn’t the shark vacuum’s brush spinning?
Having a lot of hair and other debris on the brush roll could be the reason why the shark vacuum brush is not spinning. Press the brush roll access buttons and remove the brush roll from the vacuum cleaner to remove any hair collected there.
Do you know if you can fix a Shark vacuum?
The business concept for Shark is relatively straightforward. There’s a vacuum cleaner on the market with decent performance, but it breaks down quickly and can’t be repaired.
What could be wrong with the shark vacuum motor?
Disconnect the power cord from your vacuum. Make sure your filters and hoses are clear of obstructions. Once the blocks have been removed, and the filters have been thoroughly cleaned, you should run the system one more time. Restart vacuuming by turning on the machine once again.
What do you do if your vacuum brush comes to a halt?
If the drive belt is worn or broken, you should replace it. Brush roll bearings may be clogged with hair if the drive belt is fine, but if the brush roll still won’t spin, inspect the brush roll bearings for debris.