How To Remove GPU From Motherboard? Full Procedure

Here’s a step-by-step tutorial on How To Remove GPU From Motherboard? While uninstalling a GPU is a straightforward procedure, it is critical to use attention whenever dealing with your system to avoid any harm.  When working on computers, it is advised that you wear an anti-static wrist or ankle band.

An alligator clip is commonly attached to the other side of the anti-static band. Make sure the alligator clip is attached to something unpainted on your PC casing. Because static electricity can harm or even damage computer components, wearing one of these wristbands is a simple way to ensure you don’t harm anything while functioning on your computer.

How To Remove GPU From Motherboard?

To pull the card from the slot, gently lift the lever on the expansion slot. 5. Remove the graphics card from the computer by sliding it out of the slot.

You’re able to delete your existing graphics card once you’ve obtained the necessary tools and done the necessary changes.

Remove The Case From Your Computer

To begin the procedure, your case should be open. Eliminating the side panel is always the first step in opening the case. The side panel is normally kept in place by a few metal bits or clamps that can be removed without the use of any equipment.

If your case uses standard screws, though, you’ll need to use the special screwdriver to remove them. The graphics card is usually situated in the lower area of the motherboard, in a PCIe slot. It’s difficult to overlook, especially if you disconnected the wires on the backside of your CPU yourself.

Disconnect The GPU

A PCI-e slot is used to connect Graphics Cards To The Motherboard. If your GPU isn’t too old, there’s a good possibility it’s kept in place by a screw that connects the graphics card’s metal panel to the case. This configuration eliminates the need for the graphics card to rely on the PCI-e slot for connectivity.

Take A Screwdriver And Loosen It

Loosen the screw on the outside of the case once you’ve confirmed the location of your GPU. The screws on the outside of the case may be hidden behind a plastic panel. As a result, constantly double-check that you’ve kept an eye on all of the important details. Once you’ve completely loosened the screw, you’ll see that the GPU’s hardness to the MoBo reduces, making it simpler to remove.

Pull Out The Clip

Graphic cards these days commonly have either 6-pin or 8-pin ports. You’ll probably see little clips at the top of the connector that is essential for locking the attachment. Make sure your card isn’t connected to anything else before you remove the power cord. Once the clip has been pin-pointed, begin pushing it forcefully with your finger and progressively release the wire connectors.

Depress The Release Tab

A release tab secures the graphics card in the PCI-e slot. Push down this tab at the bottom of the PCI-e slot as the final step before totally unplugging your graphics card. If you can’t reach the tab with your finger, the simplest solution is to use a non-conductive device that you can grip with both hands.

Hold the GPU in one hand and use the other to gently press down on the tab with the help of an item until you hear a click. After that, slowly pull the graphics card apart from the board while keeping the tab pressed down. You should be able to safely remove the GPU from the case at this point.

Do not pull it out hastily, and handle it with extreme caution. You should not physically remove the video card for any reason since it may be damaged. This activity may result in damage to both the GPU and the PCI-e slot.

How To Install A Graphics Card?

If you’re Replacing Your Graphics Card to exchange it with a new one, this should be a much simpler process. Your better graphics card can now be installed in the open & unrestricted PCI-e slot.

To secure the card, place it snugly in the slot and squeeze down the metal clamp on the PCI-E slot’s end. After that, use a screw to secure the GPU’s metal mount to your PC’s case. If it fits perfectly, you can use the nut that held the covering bracket on your prior GPU.

The New Video Card’s Driver

Make sure you have the correct software for your new video card, as you’ll need to install it as quickly as you restart your computer. If your modern graphics card is the same manufacturer as your old one, this step is simple. Simply go to the company’s website to download the most recent driver version for your Windows OS that matches your GPU Model.

If the GPU isn’t the same brand as the old one and you failed to remove it before removing it, you’ll have to do it again. Remove the old video card driver, then obtain or run the setup disc to download the new video card driver.

Can You Remove GPU From The Laptop?

Since laptops feature integrated graphics cards, you cannot remove the graphics card from one. Most contemporary laptops include integrated GPUs and even CPUs in the form of chips soldered to the motherboard. However, there may be a few outliers. The motherboard won’t function even if you can take it out.

Can’t Pull GPU Out?

To unlock your graphics card, use a chopstick or other culinary tool. You can attempt to gently withdraw the card while simultaneously depressing the PCI-Express port lever. Remember that you shouldn’t push yourself too much; try another approach if it doesn’t work.

Conclusion

Understanding How To Remove GPU From Motherboard? is essential, particularly if you want to advance your PC building skills. In any case, you can sell or gift your recently Removed GPU to a buddy if you will not know what to do about it.

Frequently Asked Questions