How To Connect Access Point To Wireless Router Without Cable?

Most networking managers have been using wires and cables to connect access points since you can simply connect the Wireless Access Point To A Router using an Ethernet connection and it will operate as a repeater to magnify the wireless signals for you. Connecting it wirelessly, on the other hand, is a completely different story, and there are a few things you should know about How To Connect Access Point To Wireless Router Without Cable?

How To Connect Access Point To Wireless Router Without Cable?

By setting up an access point as a wireless repeater, you can connect it wirelessly to a router without using a cable.

What Is The Best Way To Connect An Access Point To A Wireless Router Without Using A Cable?

The first question that will come to mind before doing something like this is whether it is possible to make something like this function, and here is where you should begin.

Yes, you can connect your Access Point to a Wireless Router without using an Ethernet wire. You only need to be cautious about a few things, such as compatibility and proper configuration.

To begin, you must confirm that not only the router and access point are capable of connecting wirelessly, but also that they are compatible with one another. This can be easily resolved by confirming that both the router and the access point are of the same brand, or by checking their compatibility online. After you’ve confirmed that they’re compatible, you’ll need to set them up, which you may accomplish in the following way:

How To Connect A Wireless Access Point To A Router Without Using A Cable?

The majority of access points available on the market are set to the default mode for usage as wireless access points, so you won’t have to worry about that. They enable you to increase the range of a wireless signal that is currently being broadcast by your router. Most of the time, you’ll need a computer or laptop linked to the router, but any other device would suffice.

So, once your laptop or PC is connected to the same network as the Access Point, you’ll need to utilize the access point admin panel to set it up in AP mode with the network credentials you used on the Wireless Router and intend to connect to the Access Point.

Once you’ve entered the credentials and the Access Point is within range of receiving enough Wi-Fi signals, everything should work fine, and you’ll be able to connect them Wirelessly Without Using An Ethernet Cable.

How To Connect An Access Point To A Wired Network?

The First Step Is To Set Up The Router/Switch

Install a router or switch if you haven’t already: Locate a suitable location for the gadget. If it’s a wireless router, install it where it’ll be most useful, keeping the access point’s prospective location in mind. This ensures that coverage is distributed evenly and that interference is kept to a minimum. If it’s a switch or a wired router, make sure it’s in a place where it won’t interfere with other activities or interior solutions.

Plug the router into a wall outlet and turn it on. PoE-compatible devices will just need an Ethernet wire and will not require a power outlet. In addition, some devices switch on automatically as soon as they are plugged in.

Place The Access Point In The Appropriate Location

Put the device in a convenient location. Place the access point in a location where its wireless signal will have minimal or no interference with other wireless devices on the LAN and will offer effective coverage of the premises if the local area network includes additional wireless devices, such as a router. If the access point’s objective is to add a wireless connectivity to a wired LAN, put it where the wireless signal can cover the most area with the fewest obstructions and interference.

Connect the device to the access point and connect it to an electrical outlet if it is powered by an AC/DC adaptor. Proceed to the following step if you have a PoE connection.

Connect The Cable

1. Connect the access point to the router with an Ethernet cable. The cable should be plugged into a LAN port on the router and the access point’s main Ethernet port. The access point is now connected to the router’s newly constructed local area network.
2. Connect the router to the PC with an Ethernet wire. The cable should be plugged into the router’s LAN port and the computer’s Ethernet port (typically there is only one). This connects the computer to the network and gives it access to the network’s direct access point and LAN management.
3. Use an Ethernet cable to connect the router to the modem if providing Internet access across the local area network is required. Connect the Ethernet wire to the router’s primary Ethernet port and the modem’s Ethernet port (typically there is only one).

Configure

Manual LAN setup, let alone Internet connection configuration, is nearly obsolete thanks to modern technologies. The user is ready to go once everything is correctly linked and the devices have recognized each other’s presence on the network.

If any basic configuration is required, either for the access point or for the network as a whole, the computer or the user manual should include instructions on how to proceed. Users can also adjust advanced and optional router settings by connecting to the router using the IP address 192.168.0.1 or 192.168.1.1 from a computer (or the address noted in the manual).

Make Your Access Point Experience Easier

The Infinity line from LigoWave includes three versions of universal wireless access points that provide consumers with unrivaled power and simplicity. With its excellent 720MHz processor and high-performance unidirectional dual-band antennas, the latest edition to the Infinity series redefines the notion of “power.” The NFT 3AC wireless access point delivers a stunning 1.75Gbps of fine aggregates throughput by fully utilizing 3G MIMO technology—more than enough to suit any local area network need.

Simplicity is essential for making a great product even better. This is why the Infinity line of access points is built to take convenience to the next level. These gadgets are ready to use right out of the box, and the setup process is virtually non-existent. Plug it in simple and now use it! The Infinity line of access points is a professional solution that can be implemented quickly. Because it is both strong and easy, it allows all of its users to do more with less.

How To Connect The Access Point To The Router?

Connect the access point and router with an Ethernet connection. The main Ethernet port on the access point and a LAN port on the router should receive the cable. This connects the access point to the local area network that the router has established. Connect the router and computer using an Ethernet connection.

How To The Setup Access Point With A Wireless Router?

To setup up the access point’s wireless settings, attach it to one of the ports on your current wired/wireless router.

1. Enter the access point’s default IP address, “192.168….,” to access the web-based configuration page.
2. Click Wireless on the web-based setup page.
3. Put the network name in (SSID).

Conclusion

It can be difficult to run a physical cable from one room to another in the house since it appears dirty until it is not underground. If you want to increase your home’s Wi-Fi signal, you can add another router. To improve the Wi-Fi signal, configure the second router as a repeater mode. You’ve learned all about How To Connect an Access Point To Wireless Router Without Cable?

Frequently Asked Questions