A0 Motherboard Code But No Display (Causes + Fix)

Your computer is now on, the fans are running, the case is beeping, and some lights are on. The monitor, however, displays no vital indicators, not a single picture, light, or description. The good thing is that you’re not alone, and we’ve compiled a list of every potential reason and solution for your problem. Read on to eliminate your headache caused by the A0 Motherboard Code But No Display.

How To Fix A0 Motherboard Code But No Display?

Start The PC From Scratch

 Your computer may occasionally refuse to exit Standby, Rest, or Hibernate mode, giving you the impression that it is functioning without a display.

There are various reasons for that. You may have deactivated your mouse or keyboard, or your PC won’t respond to power-saving settings or Fast Startup. Hold the power switch for a few seconds to complete a full shutdown to rule out this scenario.

Then switch it back on to observe the issue disappear. Investigate the problem’s origins and discover a means to stop it from happening again if it appears to solve everything.

Check Your Monitor

Before you start troubleshooting procedures, ensure the display is operating properly. One approach is to match it with an extra PC case and see if the problem goes away. Disconnect your monitor from the system and turn it on independently if you don’t have access to another computer.

If it isn’t broken, your monitor should light up, brighten up, or greet you with an on-screen prompt. Although there is some signal from your monitor, it is not strong enough to display a picture. If this is the case, you must move on to the subsequent checks; if not, you must send the monitor for repair.

Check The Connections

Even a faultless monitor may not turn on because of network problems. As your next step in the diagnostic process, it is worthwhile to examine all the connected wires, ports, and adapters. Assure the screws holding the video and power wires together at both ends are tight.

Test your power cord and graphic cord with different outlets and ports. Try a different cable to see if anything changes; if not, your cords may be destroyed. If your monitor allows it, you can also try a new cable type; for example, if you’re currently using VGA, connect your display using an HDMI cable.

Adapters should be the last thing you examine to ensure they are functioning properly and in good shape.  DVI to VGA converters, for instance, cannot function in the opposite direction.

Level Up Brightness

Computer displays can be completely dimmed down to the point where you cannot see a pixel. As a result, you can confuse the situation with the booting problem with no display. Check to see whether the issue is resolved for you by increasing the brightness using the keyboard shortcuts.

Try Shortcuts

If your computer doesn’t wake up, try pressing Windows, Ctrl, Shift, and B simultaneously. The command restarts the graphic driver, enabling a functional monitor to be used when your system boots. Make sure you haven’t enabled the “view on second display only” option before beginning the hardware troubleshooting. To verify this:

Press the Windows and P keys simultaneously to access the display switch menu. To access the next display mode, press Enter after pressing the P key briefly. Four display options are available: “PC screen only,” “Duplicate on the second display,” “Extend across all displays,” and “Second screen only.” To ensure you haven’t missed any, you must perform this step four times.)

Lower The Screen Resolution

The likelihood is that you have set the resolution too high, and the display cannot support it if the black screen issue returns after changing the monitor resolution. As a result, it offers nothing. In this situation, reset the monitor to the earlier supported rate to display once again. Resetting your monitor to its default settings is the recommended course of action.

Restart The Computer

• The steps to perform a monitor reset may differ based on the brand of your monitor, but generally speaking, they go like this:
• To find the control buttons, look at your display’s sides, back, or bottom.
• Squeeze the menu button, then choose “RESET” using the down/up arrows.
• Confirm your decision and follow the on-screen instructions.
• Your computer should load with the display on if you restart it.

Alternative Method

To lower the resolution value on a laptop or monitor without physical switches, consider the following alternate method:

• Restart your computer and listen for the brief beep noises.
• Hit Enter after pressing the up arrow on the keyboard.
• While pressing “Tab,” hold down the “Shift” key.
• Now, repeatedly push the right arrow four times.
• Tap the keyboard once more.
• Reduce the resolution rate with the left arrow, then press Enter.

Start The Computer In Safe Mode

Start your computer in Safe Mode if you cannot reset the monitor. By loading your system at the lowest resolution possible, this feature enables you to view Settings and return everything to normal. This is how:

• Turn the computer on and off once more.
• Keep pressing and holding the F8 key as the computer boots up.
• There will be several choices; select “Safe Mode” from among them.
• Go to System Settings now and decrease the resolution in the same manner as you did when you increased it:
• You may access the Start menu by clicking the Windows icon in the lower-left corner of the screen.
• To access your Windows Settings, click the tiny gear symbol.
• Select Display resolution under System > Display > Scale & Layout.
• Try to maintain the suggested rate and save the adjustments.

Tweak The Voltage Selector Switch

Your computer’s Voltage Selector Switch is a physical button on the back that you can use to balance your device’s internal circuit with the input voltage level. If configured incorrectly, this mechanism exceeds or falls short of the power supply’s input voltage, which hinders your PC’s ability to boot.

Most of the time, the Voltage Switch’s default setting doesn’t need to be changed because it complies with your country’s regulations. If you recently moved to a different nation or purchased it abroad, you must make certain adjustments.

For instance, your PC can happily operate with 110 Volts in the US. You might need to upgrade it to 230 Volts if you reside in Europe. The appropriate values for every country are shown in this chart.

Listen To The Beep Sounds

For hardware faults during startup, most PCs have an internal motherboard speaker. When you press the power button, this speaker typically emits one or two brief beeps, signaling that the BIOS has successfully loaded the computer.

The sound produced could be different when your computer starts up without a display. The beeping’s rhythm, length, and order may change depending on what is malfunctioning.

Please pay close attention to the sound, write down the pattern, then look it up in your motherboard handbook. This guidebook can also be used to help you comprehend what the speaker is saying if you’ve misplaced it. Your memory modules, graphics card, connections, or CPU could all be having issues. The inconvenience becomes simple to overcome once you have decoded the sound.        

Disconnect All The Peripherals

A peripheral compatibility problem may occasionally bring on your computer’s no-display problem. Switch off your computer, then disconnect as many USB devices as possible. They could be anything from your Bluetooth, keyboard, mouse, and cameras to speakers, scanners, and other electronic devices.

Then, turn on your computer by pressing the power button. Reconnect the peripherals one at a time to identify the primary offender if the problem appears to have been resolved. To stop the problem from happening again, try one or more strategies: Update the related driver (we’ll describe how to do this in the following sections). To report a problem and obtain assistance, get in touch with the manufacturer’s support staff.

Check the public forums to discover if other users have encountered the same problem and how they planned to resolve it after conducting a name and model search for the device. Switch out the problematic device for a compatible one.

Clear The BIOS Configs

The BIOS, which stands for Basic Input/Output System, is an internal program that your CPU runs to launch your OS. It can be to blame as a crucial boot-up program if your computer starts on but displays a blank screen.

Any software setup error could prevent the system from loading. The good information is that even though a dead screen prevents you from accessing the settings, you can still clear its memory by going to the motherboard’s BIOS chip.

• Your BIOS will then be reset to its initial state as a result.
• For roughly 10 seconds, press the power button to turn the device off and let the static electricity out.
• Shut off the device’s power supply.
• To reach your computer’s motherboard, open the chassis.
• Find the CMOS coin cell battery and, if present, flip up the protective clip.
• The battery will come up from its position once you slip your finger below it.
• Give it roughly five minutes before replacing the battery and reconnecting the power.

Update Your Drivers

Your PC may become so damaged that it can no longer start up, whether the driver is for the graphics cards, a particular device, or necessary hardware. The no-display problem may be magically resolved by updating these files. The problem is that you can’t access Settings to update anything unless the screen is turned on.

You’re good to go if you’ve successfully fixed the monitor’s display by removing the problematic device. If you haven’t already, try starting your computer in Safe Mode so you can see the system’s default settings. Next, carry out the subsequent actions:

• In the taskbar’s search box, enter “Device Manager.”
• To launch the app, select the first result.
• Depending on the driver you wish to update, expand a category.
•  (It may go under the display adapter’s category or another peripheral category like Bluetooth, Keyboards, Cameras, etc.)
• Then, from the list of entries, right-click the name of the desired device.
• After selecting “Update Driver,” follow the on-screen instructions.

What Does A0 Mean On My Motherboard?

A0 typically denotes a defective CPU or DIMM. Nevertheless, the motherboard is another potential culprit.

What Does A0 Mean On A Gigabyte Motherboard?

The A0 code indicates that the computer has adequately booted up and handed over control of the PC to the operating system on most motherboards (Asus and MSI, for sure).

Conclusion

Hopefully, this solution to A0 Motherboard Code But No Display should have been helpful. Please let me know which approach worked for you or if you have other suggestions for resolving this problem. Your opinions would be appreciated!

Frequently Asked Questions